The Stanley Hydraulic GR29 Grinder is a right angle grinder ("vertical grinder") that can be used for grinding and cleaning in underwater applications with a variety of wheels, brushes and attachments. The high torque gear motor drives a standard 5⁄8 - 11 threaded spindle. A 9" adjustable wheel guard, two position assist handle and trigger guard are standard. Painted hi‑visibility yellow.FEATURES:Integral Stanley Hyrevz gear motor produces high torqueStainless Steel spools and fastenersTwo position assist handle for right/left hand operationOversized trigger with guard for diver comfortAdjustable wheel guard for infinite positionsPlastisol covered handle for comfortable ergonomic gripUse with grinding wheels, hull scrubbing brushes, wire and nylon brushes, barnacle busters and Desmond wheels3200 rpm @ 12 gpmCast-in lifting eyeSPECIFICATIONS:Capacity: 9" / 23 cm Wheel Spindle: 5⁄8" – 11 Threaded Circuit Type: Open Center Flow Range: 4-12 gpm / 15-45 l/minWorking Pressure: 1000-2000 psi / 70-140 barFull Relief Setting: 2250 psi / 155 bar RPM: 3200 @ 12 gpm / 45 l/minWeight (with guard): 15 lbs / 6.8 kgLength: 11" / 28 cm Width (with guard): 10¼" / 26 cmHydraulic Ports: -8 SAE O-ring Connection Size and Type: 3⁄8" Male Pipe AdapterCouplers: Varies with model (See Ordering Information)Hose Whips: No (See Accessories)Delivery without disc (please order separately)

Stanley’s GR30 Grinder embodies the latest product improvements in this tool. The vertical grinder now has the Stanley Dual Spool Selector which allows the tool to be set for either open-center or closed-center systems.All the screw fasteners are stainless steel. The trigger spool is stainless steel. A trigger lock prevents accidental starting of the grinder.The integral Stanley HyrevzTM gear motor is manufactured to exacting standards to deliver maximum efficiency.The over-sized motor run-down valve allows the motor to freely run down in speed when the grinder is turned off ensuring that a properly installed wheel will not spin off the spindle.The built-in reverse-check valve in the handle prevents operating the grinder when reverse-plumbed to the hydraulic system. Preventing reverse operation ensures a long operating life for the hydraulic seals.The thick, tough layer of foamedplastisol covering the handle transmits very little heat. The foamed plastisol gives a more comfortable grip to the tool.The cast-in lifting eye is always available, unlike screwed-in lifting rings which may come loose and fall off.The Stanley dual-spool selector is accessable under a seal plug at the rear of the tool. Setting the tool  for open- or closed-center operation is as simple as opening or closing a valve.The selector is not susceptible to moving under the vibration of use and is completely protected from  accidental or unintentional access. The seal plug also protects the end of the trigger spool and dual-spool selector from water and dirt.There are two positions available for the assist handle to be conveniently placed by the operator. Eitherposition is at a most comfortable handling position from the valve handle.The wheel guard is adjustable. By loosening the clamp screw which has an integral toggle handle, the  guard may be rotated to any convenient position.The grinders can be used with standard grinding wheels and brushes that are rated for at least 6500 rpm and have a hub with 5/8-11UNC straight thread.CAPACITY: 9 in. Wheel on 5/8-11 thrd arborSPEED: 5600 rpm at 8 gpm (30 l/min)INPUT FLOW RANGE: 7-9 gpm 26-34 l/minINPUT PRESSURE: 1000-2000 psi 70-140 bar WEIGHT: 12.5 lbs. 5.7 kg LENGTH: 8.5 in. 21.6 cm WIDTH: 8.7 in. 22.1 cm HEIGHT: 17.5 in. 44.5 cm MOTOR: Stanley HyrevzTM Gear PORTING: -8 SAE O-ring HOSE WHIPS: Yes, includes Speed LimiterDelivery without disc (please order separately)

The HYCON PREMIUM Cut-off Saw cuts all types of concrete, steel, brick wall, asphalt etc. The HYCON Cut-off saw is a very sturdy tool intended for cutting even under the most extreme conditions. It is completely unaffected by water and dust, and all parts run in oil. The HYCON PREMIUM-saws are build for hard use day after day - without breakdowns. The fact, that the saw is always working and does not require service means higher profits than with e.g. a petrol saw. The saw stops automatically if the blade jams because of the system pressure relief valve. The blade stops rotating maximum 10 sec. after releasing the trigger. Assuring no injury to the operator. The hydraulic cut-off saw from HYCON can be used for horizontal and vertical cutting. Hydraulic direct drive high quality motor assume a minimum of service. Flushing water runs through body and hydraulic motor for extra cooling and to keep all surfaces cold.Saw blade diameter: 450 mm Hydraulics: 20-40 L / min at 120 bar max. 172 bar Cutting depth: 187 mm Peripheral speed of the saw blade: 79 m / s Weight: 8,1 kg

The HYCON PREMIUM Cut-off Saw cuts all types of concrete, steel, brick wall, asphalt etc. The HYCON Cut-off saw is a very sturdy tool intended for cutting even under the most extreme conditions. It is completely unaffected by water and dust, and all parts run in oil. The HYCON PREMIUM-saws are build for hard use day after day - without breakdowns. The fact, that the saw is always working and does not require service means higher profits than with e.g. a petrol saw. The saw stops automatically if the blade jams because of the system pressure relief valve. The blade stops rotating maximum 10 sec. after releasing the trigger. Assuring no injury to the operator. The hydraulic cut-off saw from HYCON can be used for horizontal and vertical cutting. Hydraulic direct drive high quality motor assume a minimum of service. Flushing water runs through body and hydraulic motor for extra cooling and to keep all surfaces cold.Saw blade diameter: 350 mm Hydraulics: 20-30 L / min at 120 bar max. 172 bar Cutting depth: 137 mm Peripheral speed of the saw blade: 71 m / s Weight: 7.4 kgDelivery without disc (please order separately)

The HYCON Cut-off Saw PREMIUM cuts all types of concrete, steel, brick wall, asphalt etc. The HYCON Cut-off saw is a very sturdy tool intended for cutting even under the most extreme conditions. It is completely unaffected by water and dust, and all parts run in oil. The HYCON PREMIUM-saws are build for hard use day after day - without breakdowns. The fact, that the saw is always working and does not require service means higher profits than with e.g. a petrol saw. The saw stops automatically if the blade jams because of the system pressure relief valve. The blade stops rotating maximum 10 sec. after releasing the trigger. Assuring no injury to the operator. The hydraulic cut-off saw from HYCON can be used for horizontal and vertical cutting. Hydraulic direct drive high quality motor assume a minimum of service. Flushing water runs through body and hydraulic motor for extra cooling and to keep all surfaces cold.Assuring no injury to the operator. The hydraulic cut-off saw from HYCON can be used for horizontal and vertical cutting. Hydraulic direct drive high quality motor assume a minimum of service. Flushing water runs through body and hydraulic motor for extra cooling and to keep all surfaces cold.Saw blade diameter: 400 mm Hydraulics: 20-40 L / min at 120 bar max. 172 bar Cutting depth: 162 mm Peripheral speed of the saw blade: 81 m / s Weight: 7.8 kgDelivery without disc (please order separately)

The HYCON PREMIUM Cut-off Saw cuts all types of concrete, steel, brick wall, asphalt etc. The HYCON Cut-off saw is a very sturdy tool intended for cutting even under the most extreme conditions. It is completely unaffected by water and dust, and all parts run in oil. The HYCON PREMIUM-saws are build for hard use day after day - without breakdowns. The fact, that the saw is always working and does not require service means higher profits than with e.g. a petrol saw. The saw stops automatically if the blade jams because of the system pressure relief valve. The blade stops rotating maximum 10 sec. after releasing the trigger. Assuring no injury to the operator. The hydraulic cut-off saw from HYCON can be used for horizontal and vertical cutting. Hydraulic direct drive high quality motor assume a minimum of service. Flushing water runs through body and hydraulic motor for extra cooling and to keep all surfaces cold.Saw blade diameter: 450 mm Hydraulics: 20-40 L / min at 120 bar max. 172 bar Cutting depth: 187 mm Peripheral speed of the saw blade: 79 m / s Weight: 8,1 kgDelivery without disc (please order separately)

The HYCON PREMIUM Cut-off Saw cuts all types of concrete, steel, brick wall, asphalt etc. The HYCON Cut-off saw is a very sturdy tool intended for cutting even under the most extreme conditions. It is completely unaffected by water and dust, and all parts run in oil. The HYCON PREMIUM-saws are build for hard use day after day - without breakdowns. The fact, that the saw is always working and does not require service means higher profits than with e.g. a petrol saw. The saw stops automatically if the blade jams because of the system pressure relief valve. The blade stops rotating maximum 10 sec. after releasing the trigger. Assuring no injury to the operator. The hydraulic cut-off saw from HYCON can be used for horizontal and vertical cutting. Hydraulic direct drive high quality motor assume a minimum of service. Flushing water runs through body and hydraulic motor for extra cooling and to keep all surfaces cold.Saw blade diameter: 500 mm Hydraulics: 30-40 L / min at 120 bar max. 172 bar Cutting depth: 212 mm Peripheral speed of the saw blade: 59 m / s Weight: 9,2 kgDelivery without disc (please order separately)

Drehzahl: 3000 U/minDurchmesser Schleifscheibe: 200 mm Lochdurchmesser: 13-32 mm Scheibenbreite: 9-32 mm Ölmenge: 17-34 L/min bei max. 210 bar

Drehzahl: 3000 U/minDurchmesser Schleifscheibe: 200 mmLochdurchmesser: 13-32 mmScheibenbreite:  9-32mmÖlmenge: 12-24 L/min bei max. 210 bar 

Diamantring YELLOW Premium 20 f ür Stahlbeton, Beton, Granit Ringdurchmesser: 400 mm

All parts run in oil - no downtime and almost maintenance-free. The HYCON ring saw has a unique design and a state-of-the-art drive mechanism, which, thanks to durable wear parts, guarantees maximum reliability and low operating costs. The purchase of a HYCON HRS400 ring saw is an investment in more depth of cut that similar tools cannot offer. Ring diameter: 400 mm Hydraulics: 30-40 L / min at max. 160 bar Cutting depth 300mm

for concrete

for concrete

for concrete

for concrete

Hydraulik: 20 L/min. bei 140-180 barScheibendurchmesser: Ø 180 mmSchnitttiefe bei 90°: 60 mmSchnitttiefe bei 45°: 35 mmAufnahme: Ø 16/19/20/30 mmLeistung: 2,3 kWSchalldruckpegel (LpA): 85 dB(A)Vibrationswert: < 2,5 m/s²Gewicht: 10,2 kgLieferung ohne Sägeblatt (bitte extra bestellen)Optional lieferbar:Hartmetall-Sägeblätterfür Trockenschnitt geeignetfür Kunststoff, Plexiglas, Aluminium, Stahl, Edelstahl, Kupfer

Hydraulik: 20-23 L/min. bei 140-180 barScheibendurchmesser: Ø 320 mmSchnitttiefe bei 90°: 120 mmAufnahme: Ø 25,4 mmLeistung: 2,3 kWSchalldruckpegel (LpA): 85 dB(A)Vibrationswert: < 2,5 m/s²Gewicht: 12,2 kgLieferung ohne Sägeblatt (bitte extra bestellen)Optional lieferbar:Hartmetall-SägeblätterØ 230 mm, Ø 320 mmfür Trockenschnitt geeignetfür Kunststoff, Plexiglas, Aluminium, Stahl, Edelstahl, Kupfer

The CO23 Cut-Off Saw is a hydraulic powered saw for dimensional cutting of metal, concrete, rock, masonry and coral. It has a high torque gear motor and 10" blade capacity for abrasive and diamond wheels with a 1" arbor. The CO23 is designed for underwater operation and is painted hi-visibility yellow.Features:Integral Stanley Hyrevz gear motor produces high torque Direct drive motor Stainless Steel spool and fasteners Adjustable shoe for precise cuts Interlocking safety trigger Cast aluminum handle and guard for durability Counter-clockwise rotation Wide flow rangeDelivery without disc (please order separately)Specifications:Capacity: 10" / 25.4 cm wheel Performance: 3275 rpm @ 15 gpm Arbor:  1" / 2½ cm Circuit Type: Open Center Flow Range: 10-15 gpm / 38-57 l/minOptimum Flow: 15 gpm / 57 l/minWorking Pressure: 1500-2000 psi / 105-140 barFull Relief Setting: 2250 psi / 155 bar Weight: 23 lbs / 10.4 kg Length: 19½" / 49½ cm Width: 11" / 28 cm Hydraulic Ports: -8 SAE O-ring Connection Size and Type: ½" Male Pipe Hose EndCouplers: No (See Accessories) Hose Whips: Yes

Lightweight and Powerful, the Stanley CO23 Underwater and CO25 Cutoff Saws are ideal for cutting concrete, masonry, pipe, structural steel beams and guardrail.CO25 Land Model Multi-Hand Position Cast Aluminum Handle with Interlocking Safety Trigger provides ergonomic grip at a variety of tool angles for reduced operator fatigue.Tamper-Proof Flow Control meets ANSI specification for speed control, reducing the risk of over-speeding the cutting wheel.Cutoff Saws can be used with readily available standard abrasive wheels and wet or dry diamond blades.Internal Blade Brake retards spindle rotation upon release of trigger to greatly reduce wheel coast time.Adjustable Cast Aluminum Wheel Guard is designed to provide excellent durability, allow cutting near obstructions and minimize tool weight.Available Handle Extension Kit provides for upright operation to meet operator preference.OUTPUT CAPACITY 14 in wheel 35.6 cmINPUT FLOW RANGE 7 - 9 gpm 26 - 34 lpmINPUT PRESSURE 1500 - 2000 psi 105 - 140 barOPTIMUM FLOW 8 gpm 30 lpmWEIGHT 20.00 lbs. 9.1 kgLENGTH 21 in 53.3 cmWIDTH 11 in 28 cmMOTOR HYREVZTM GearPORTING 8 SAE O-RingCONNECTOR 3/8 in Male Pipe Hose EndDelivery without disc (please order separately)