Oil spill clean-up systems

The KWF WATER HBW200 hydraulic high-pressure cleaner from FEP is the perfect solution for mobile use on commercial vehicles and vans weighing up to 7.5 tonnes. The powerful high-pressure cleaner pump, driven by a hydraulic motor, delivers a water flow rate of 25 litres per minute at a pressure of 150 bar. As it is driven directly by the vehicle’s engine, no harmful exhaust fumes are produced by the unit, enabling safe operation even in the load compartment. The KWF WATER HBW200 requires a hydraulic supply of 20–40 litres at 200 bar and is fitted with a pressure gauge and a pressure relief valve. The system is optionally available with a 90-litre water tank. It is conveniently operated via a wash lance with high- and low-pressure nozzles, connected to an automatic hose reel with 18 metres of hose. Its compact dimensions of 445 x 720 x 500 mm (height) make it easy to integrate into existing vehicle bodies. Discover all the applications for hydraulic systems in commercial vehicles on our overview page: Hydraulics for commercial vehicles and vans up to 7.5 tonnes! High-pressure cleaner pump with a hydraulic motor, delivering a water flow rate of 25 litres per minute and a pressure of 150 bar.As it is driven by the vehicle’s engine, the unit produces no harmful exhaust fumes, enabling safe operation in the load compartment.FeaturesHydraulic requirements: 20–40 litres at 200 bar Pressure gauge and pressure relief valveAvailable with a 90-litre water tankWashing lance with high- and low-pressure nozzles, mounted on a hose reel with an automatic spring-loaded drum and a hose length of 18 metresDimensions: 445 x 720, height 500 mm

The ROAD CLEANER RC-H is the compact solution for removing oil spills in vans such as the VW T6.1, VW Crafter FWD or FIAT Ducato, which do not have a power take-off (PTO). As it is powered by the vehicle’s engine, no harmful exhaust fumes are produced, allowing for safe operation in the load compartment. The system combines a high-pressure cleaner and a vacuum extractor, with the extracted liquid being collected in a stainless steel tank. The hydraulic system requires 15 litres at 180 bar and is protected by a high-performance cooling system. Further safety features include a thermal protection switch, oil level monitoring, a pressure relief valve and an emergency stop switch. The unit is powered by the 12-volt on-board electrical system. A 300-litre stainless steel water tank, a 5-litre detergent tank, a wash lance, a hydraulic vacuum suction unit with a 3-metre suction height, and a hose reel with a 10-metre suction hose are already integrated. The system is approved for ATEX-1 and ATEX-21 zones and is ideally suited for use in potentially explosive atmospheres. You can find more information about the manufacturer here: FEP at KW Hydraulik. Application example: Hydraulics for commercial vehicles and vans up to 7.5 tonnes. This model can be fitted to vans that do not have a gearbox with a power take-off (PTO).VW T6.1, VW Crafter FWD, FIAT Ducato, ...As it is driven by the vehicle’s engine, no harmful exhaust fumes are produced at the unit, enabling safe operation in the load compartment.The hydraulic system drives either the high-pressure cleaner or the vacuum cleaner.The extracted liquid is collected in a stainless steel tank.The unit can be used in potentially explosive atmospheres classified as ATEX-1 and ATEX-21.FeaturesHydraulic system: 15 litres at 180 bar Hydraulic system with high-performance cooling. Thermal protection switch, oil level monitoring Pressure gauge and pressure relief valve Control system with operating hours counter Emergency stop switch (disconnects the system from the drive) 12-volt on-board power supply for system control 300-litre stainless steel water tank with water separator 5-litre tank for cleaning additive with proportioning control Brush for vacuum unit Washing lance with high- and low-pressure nozzles Hydraulic vacuum suction unitSuction height: 3 metres Spring-return hose reel for suction hose, 10 metres, hose diameter 38 mm40-litre tank for collecting the oil-water mixture, with automatic shut-off when the tank is full Approved for ATEX-1 and ATEX-21 zones Dimensions: 1400 x 1100 x H1250 mm Model ROAD CLEANER RC-HC with additional gas-fired water heater.

The ROAD CLEANER RC-H2 is the professional solution for removing oil marks in vehicles with a power take-off (PTO), such as the VW Crafter, MAN TGE, Mercedes Sprinter, IVECO Daily or Renault Master. It is powered by the vehicle’s engine – no harmful exhaust fumes are produced, enabling safe operation in the load compartment. Thanks to the simultaneous use of a high-pressure cleaner and a vacuum extractor, water consumption is reduced and cleaning is carried out more quickly and in a more environmentally friendly manner. The extracted liquid is collected in a stainless steel tank. The system meets the requirements for ATEX-1 and ATEX-21 zones. Technical specifications: Hydraulic flow requirement 15 l/min at 180 bar, high-performance cooling, emergency stop switch, operating hours counter, 300-litre water tank, 10-metre suction hose and 40-litre collection tank with automatic shut-off. You can find more information about the manufacturer here: FEP at KW Hydraulik. Applications: Hydraulics for commercial vehicles and vans up to 7.5 tonnes. This model is designed for installation in vehicles with a transmission power take-off (PTO).VW CRAFTER / MAN TGEMERCEDES SPRINTERIVECO DAILYRENAULT MASTER / OPEL MOVANO / NISSAN NV400As it is powered by the vehicle’s engine, no harmful exhaust fumes are produced at the unit itself, enabling safe operation in the load compartment.With this drive option, the high-pressure cleaner can be operated simultaneously with the vacuum cleaner.This method requires less water, makes the work quicker and is more environmentally friendly.The extracted liquid is collected in a stainless steel tank.The unit can be used in potentially explosive atmospheres classified as ATEX-1 and ATEX-21.FeaturesHydraulic system: 15 litres at 180 bar Hydraulic system with high-performance cooling. Thermal protection switch, oil level monitoring Pressure gauge and pressure relief valve Control system with operating hours counter Emergency stop switch (disconnects the system from the drive) 12-volt on-board power supply for system control 300-litre stainless steel water tank with water separator 5-litre tank for cleaning additive with proportioning control Brush for vacuum unit Washing lance with high- and low-pressure nozzles Hydraulic vacuum suction unitSuction height: 3 metres Spring-return hose reel for suction hose, 10 metres, hose diameter 38 mm 40-litre tank for collecting the oil-water mixture, with automatic shut-off when the tank is fullApproved for ATEX-1 and ATEX-21 zones Model ROAD CLEANER RC-H2C with additional gas-powered water heater.

The ROAD CLEANER RC-H2C combines a high-pressure cleaner, a hydraulic vacuum cleaner and a gas-powered water heater for efficient use in vehicles with a power take-off (PTO), such as the VW Crafter, the MAN TGE, Mercedes Sprinter, IVECO Daily or Renault Master. It is powered by the vehicle’s engine, meaning no harmful exhaust fumes are produced by the unit itself – ideal for safe use in the load compartment. The ability to carry out cleaning and extraction simultaneously minimises water consumption and reduces working time. The extracted liquid is collected in a robust stainless-steel tank. The ROAD CLEANER RC-H2C is also approved for use in potentially explosive atmospheres (ATEX-1 and ATEX-21). Technical highlights: Hydraulic flow requirement 15 l/min at 180 bar, high-performance cooling, operating hours counter, emergency stop switch, 300-litre water tank, a 10-metre suction hose and a 40-litre collection tank with level-controlled shut-off. You can find more information about the manufacturer here: FEP at KW Hydraulik. Applications: Hydraulics for commercial vehicles and vans up to 7.5 tonnes. This model is designed for installation in vehicles with a gearbox power take-off (PTO):VW CRAFTER / MAN TGEMERCEDES SPRINTERIVECO DAILYRENAULT MASTER / OPEL MOVANO / NISSAN NV400As it is powered by the vehicle’s engine, no harmful exhaust fumes are produced at the unit itself, enabling safe operation in the load compartment.With this drive option, the high-pressure cleaner can be operated simultaneously with the vacuum cleaner.This method requires less water, makes the work quicker and is more environmentally friendly.The extracted liquid is collected in a stainless steel tank.The unit can be used in potentially explosive atmospheres classified as ATEX-1 and ATEX-21.FeaturesHydraulic system: 15 litres at 180 bar Hydraulic system with high-performance cooling. Thermal protection switch, oil level monitoring Pressure gauge and pressure relief valve Control system with operating hours counter Emergency stop switch (disconnects the system from the drive) 12-volt on-board power supply for system control 300-litre stainless steel water tank with water separator 5-litre tank for cleaning additive with proportioning control Brush for vacuum unit Washing lance with high- and low-pressure nozzles Hydraulic vacuum suction unitSuction height: 3 metres Spring-return hose reel for suction hose, 10 metres, hose diameter 38 mm 40-litre tank for collecting the oil-water mixture, with automatic shut-off when the tank is fullApproved for ATEX-1 and ATEX-21 zones Model ROAD CLEANER RC-H2C with additional gas-powered water heater.

The ROAD CLEANER RC-HC is a versatile high-pressure cleaner with a vacuum suction unit and a gas-powered water heater, designed for installation in vans without a power take-off (PTO), such as the VW T6.1, VW Crafter FWD or FIAT Ducato. It is powered by the vehicle’s engine – meaning no harmful exhaust fumes are produced, which allows for safe operation in the load compartment. The hydraulic system drives either the high-pressure cleaner or the vacuum suction unit. The integrated instantaneous hot-water heater makes cleaning more efficient and faster, even in cold temperatures. Liquids are reliably collected in a stainless-steel tank. The system is also approved for use in ATEX-1 and ATEX-21 zones. Technical details: Hydraulic flow requirement 15 l/min at 180 bar, high-performance cooling, 300-litre water tank, 10 m suction hose and 40-litre collection tank with automatic shut-off. Find out more about the manufacturer here: FEP at KW Hydraulik. You can find suitable applications here: Hydraulics for commercial vehicles & vans up to 7.5 tonnes. This model can be fitted to vans that do not have a gearbox with a power take-off (PTO).VW T6.1, VW Crafter FWD, FIAT Ducato, ....As it is driven by the vehicle’s engine, no harmful exhaust fumes are produced by the unit, enabling safe operation in the load compartment.The hydraulic system drives either the high-pressure cleaner or the vacuum cleaner.This version features an additional gas-powered instantaneous water heater. Hot water enables use in cold outdoor temperatures and breaks down dirt more effectively.The extracted liquid is collected in a stainless steel tank.The unit can be used in potentially explosive atmospheres classified as ATEX-1 and ATEX-21.FeaturesHydraulic system: 15 litres at 180 bar Hydraulic system with high-performance cooling. Thermal protection switch, oil level monitoring Pressure gauge and pressure relief valve Control system with operating hours counter Emergency stop switch (disconnects the system from the drive) 12-volt on-board power supply for system control 300-litre stainless steel water tank with water separator 5-litre tank for cleaning additive with proportioning control Brush for vacuum unit Washing lance with high- and low-pressure nozzles Hydraulic vacuum suction unitSuction height: 3 metres Spring-return hose reel for suction hose, 10 metres, hose diameter 38 mm40-litre tank for collecting the oil-water mixture, with automatic shut-off when the tank is full Approved for ATEX-1 and ATEX-21 zones Dimensions: 1400 x 1100 x H1250 mm Model ROAD CLEANER RC-HC with additional gas-fired water heater.

The ROAD CLEANER RC-M module is the flexible solution for removing oil marks from vehicles with a load bed or trailers. It is easy to fit and ready for immediate use – ideal for small vans or trailers too. The integrated petrol engine with electric starter drives a hydraulic pump, which supplies either the high-pressure cleaner or the vacuum extractor. The extracted liquid is safely collected in a stainless steel tank. The system is approved for use in potentially explosive atmospheres (ATEX-1 and ATEX-21) and features a 300-litre water tank, an oil cooler, an 18-metre high-pressure hose and a 10-metre suction hose. You can find out more about the manufacturer here: FEP at KW Hydraulik. You can find applications for this module here: Hydraulics for commercial vehicles & vans up to 7.5 tonnes. This moduleis idealfor use on vehicles with a load bedor on trailers.It is mounted on the load bed as required and isready for immediate use.Even the smallest vehicles and trailers canbe used for transport.The integrated motor isstarted using an electric starter. This drives a hydraulic pump, whichin turn alternatelydrivesa high-pressure cleaner anda vacuum cleaner.The extracted liquid iscollected in astainless steel tank.The unit canbe used in potentially explosive atmospheresclassified as ATEX-1 and ATEX-21.FeaturesPetrol engine with electric start (supplied without a battery and prepared for connection to the vehicle’s electrical system)Hydraulic system: 15 litres at 180 bar Hydraulic system with a 10-litre hydraulic tank and oil cooler 300-litre stainless steel water tank with water separator5-litre tank for cleaning additive with proportioning control Spring-return hose reel for high-pressure hose, 18 metres Washing lance with high- and low-pressure nozzles Hydraulic vacuum suction unit Suction height: 3 metres Spring-return hose reel for suction hose, 10 metres, hose diameter 38 mm Brush for vacuum cleaner 40-litre tank for collecting the oil-water mixture, automatic shut-off when the tank is full Approved for ATEX-1 and ATEX-21 zones Dimensions: 1400 x 1100 x H1250 mmModel ROAD CLEANER RC-MC with additional gas-fired water heater.

The ROAD CLEANER RC-M-ST is a particularly compact version designed for removing oil marks from vehicles with a load bed or trailers. Thanks to its modular design comprising three separate components (high-pressure cleaner, water tank and drive unit), the system can be installed in a particularly space-saving manner. The integrated petrol engine with electric starter drives a hydraulic pump, which supplies either the high-pressure cleaner or the vacuum extractor. The extracted liquid is collected in a stainless steel tank. Weighing just 335 kg, this model is perfectly suited to small vans and trailers. The system is approved for use in ATEX-1 and ATEX-21 zones and features a 120-litre polyethylene water tank, an 18-metre high-pressure hose reel and a 10-metre suction hose reel. You can find out more about the manufacturer here: FEP at KW Hydraulik. Find out more about suitable applications here: Hydraulics for commercial vehicles & vans up to 7.5 tonnes. A particularly compact version of the ROAD CLEANER unit. The three components – the high-pressure cleaner, water tank and drive unit – are separate and can be housed in a space-saving manner.This moduleis idealfor use on vehicles with a load bedor on trailers.It is mounted on the load bed as required and isready for immediate use.Even the smallest vehicles and trailers canbe used for transport.The integrated engine isstarted using an electric starter. This drives a hydraulic pump, whichin turn alternatelydrivesa high-pressure cleaner anda vacuum cleaner.The extracted liquid iscollected in astainless steel tank.The unit canbe used in potentially explosive atmospheresclassified as ATEX-1 and ATEX-21.FeaturesThree-element structure, modular to suit the available space Net weight 335 kgPetrol engine with electric starter (supplied without a battery and prepared for connection to the vehicle’s electrical system)Hydraulic system: 15 litres at 180 bar Hydraulic system with 10-litre hydraulic tank and oil cooler 120-litre polyethylene water tank5-litre tank for cleaning additive with proportioning control Spring-return hose reel for high-pressure hose, 18 metres Washing lance with high- and low-pressure nozzles Hydraulic vacuum suction unit Suction height: 3 metres Spring-return hose reel for suction hose, 10 metres, hose diameter 38 mm Brush for vacuum cleaner 40-litre tank for collecting the oil-water mixture, automatic shut-off when the tank is full Approved for ATEX-1 and ATEX-21 zonesModel ROAD CLEANER RC-M STC with additional gas-fired water heater.

The ROAD CLEANER RC-MC is the mobile solution for removing oil spills from vehicles with a load bed or trailers. Thanks to its compact design, the system can be flexibly fitted and put into operation immediately. The integrated petrol engine with electric starter drives a hydraulic pump, which powers either the high-pressure cleaner or the vacuum extractor. A particular highlight of this model is the additional gas-powered water heater, which facilitates use in cold temperatures and enables more effective cleaning. The extracted liquid is safely collected in a stainless steel tank. As it is approved for ATEX-1 and ATEX-21 zones, the ROAD CLEANER RC-MC is also suitable for use in potentially explosive atmospheres. The equipment includes a 300-litre stainless steel water tank, an 18-metre high-pressure hose and a 10-metre suction hose with spring retraction. You can find out more about the manufacturer here: FEP at KW Hydraulik. Suitable applications can be found here: Hydraulics for commercial vehicles & vans up to 7.5 tonnes. This module is idealfor use on vehicles with a load bedor on trailers.It is mounted on the load bed as required and isready for immediate use.Even the smallest vehicles and trailers canbe used for transport.The integrated engine isstarted using an electric starter. This drives a hydraulic pump, whichin turn alternatelypowersa high-pressure cleaner anda vacuum cleaner.This version features an additional gas-powered instantaneous water heater. Hot water enables operation in cold outdoor temperatures and removes dirt more effectively.The extracted liquid iscollected in astainless steel tank.The unit canbe used in potentially explosive atmospheresclassified as ATEX-1 and ATEX-21.FeaturesPetrol engine with electric start (supplied without a battery and prepared for connection to the vehicle’s electrical system)Hydraulic system: 15 litres at 180 bar Hydraulic system with a 10-litre hydraulic tank and oil cooler 300-litre stainless steel water tank with water separator5-litre tank for cleaning additive with proportioning control Spring-return hose reel for high-pressure hose, 18 metres Washing lance with high- and low-pressure nozzles Hydraulic vacuum suction unit Suction height: 3 metres Spring-return hose reel for suction hose, 10 metres, hose diameter 38 mm Brush for vacuum cleaner 40-litre tank for collecting the oil-water mixture, automatic shut-off when the tank is full Approved for ATEX-1 and ATEX-21 zones Dimensions: 1400 x 1100 x H1250 mmModel ROAD CLEANER RC-MC with additional gas-fired water heater.

The ROAD CLEANER RC-SC offers a particularly flexible solution for removing oil spills in vehicles with limited space. Unlike other models, this system is not mounted on a central support frame. The three-part design saves weight and allows for space-saving integration. The integrated petrol engine with electric starter drives a hydraulic pump, which supplies either the high-pressure cleaner or the vacuum cleaner. A 120-litre polyethylene water tank and a separate tank for cleaning additive ensure efficient operation. The separated liquid is safely collected in a 40-litre stainless steel tank. The unit is approved for use in ATEX-1 and ATEX-21 zones and is therefore also suitable for use in potentially explosive atmospheres. You can find more details about the manufacturer here: FEP at KW Hydraulik. Further areas of application can be found here: Hydraulics for commercial vehicles & vans up to 7.5 tonnes. This three-part model is not mounted on a central support frame. Thanks to its weight savings and flexibility, it is particularly suitable for installation in vehicles with limited space.The extracted fluid is collected in a stainless steel tank.The unit can be used in potentially explosive atmospheres classified as ATEX-1 and ATEX-21.FeaturesCleaning unit comprising three parts, total weight 335 kg Petrol engine with electric starter (supplied without a battery and prepared for connection to the vehicle’s electrical system) Hydraulic system: 15 litres at 180 bar Hydraulic system with a 10-litre hydraulic tank and oil cooler 120-litre polyethylene water tank with water separator5-litre tank for cleaning additive with proportioning control Spring-return hose reel for high-pressure hose, 18 metres Washing lance with high- and low-pressure nozzles Hydraulic vacuum suction unitSuction height: 3 metres Spring-return hose reel for suction hose, 10 metres, hose diameter 38 mm Brush for vacuum cleaner 40-litre tank for collecting the oil-water mixture, automatic shut-off when the tank is fullApproved for ATEX-1 and ATEX-21 zones Model ROAD CLEANER RC-SCC with additional gas-fired water heater.